SAGE 950RTS Options

950RTS-050 4 Port Serial I/O Card
Provides additional serial I/O ports for user access, DCS control, or switch control.

950RTS-051 8 Port Serial I/O Card
Provides additional serial I/O ports for user access, DCS control, or switch control.

950RTS-080 X.25 Networking Card & Software
Allows users to access the 950RTS via an X.25 interface at a data rate of up to a 19.2 Kbit/s.

950RTS-103 16-User Operating System
Increases the base operating system to 16 simultaneous users.

950RTS-200 Dual DS-1 (1.544 Mbit/s) PCM Interface
Can be configured as 2 terminate ports or 2 DCS ports. Supports up to 8 cards (16 DS-1 ports).

950RTS-250 Dual PCM RJ-45 Configurator Panel
RJ-45 connector panel for PCM interface. One configurator panel should be ordered for each PCM interface board.

950RTS-251 Dual PCM Wire Wrap Configurator Panel
Panel contains .045" square wire wrap pins to accommodate two PCM connections. One configurator panel should be ordered for each Dual PCM Interface board. Replaces standard Dual PCM RJ-45 Configurator Panel.

950RTS-300 Quad DSP (Digital Signal Processor) Card
Performs all DS-0 digital and analog (VF) testing. Four DSPs allow simultaneous testing of 4 different 64 Kbit Channels. Up to 8 cards (32 simultaneous tests) may be used per system.

950RTS-400 DS-0, Switched 56/64 Kbit/s, DDS BERT
BERT with all standard stress patterns for DS-0, Switched 56/64 Kbit/s, and DDS applications. Also includes user-defined patterns and both standard and user-defined loopback codes.

950RTS-401 DS-1
DS-1 with all standard and long stress patterns. Also includes user-defined patterns up to 2 Kb, and both standard and user-defined loopback codes.

950RTS-402 FT-1
Fractional T-1 with all standard and long stress patterns. Tests Contiguous, Non-Contiguous and True Non-Contiguous N x 56/64 Kbit/s data paths. Also includes user-defined patterns up to 2 KBytes, and loopback codes.

950RTS-600 Standard VF Measurements
Sends tone and measures tone level and frequency. Measures Noise (3 KHz Flat, C-Message, C-Notch and Psophometric). Sends and measures return loss test signals.

950RTS-601 Data Test VF Measurements
All VF data tests, including 3-Level Impulse Noise, Phase/Amplitude Hits and Jitter, Envelope Delay, Group Delay, Absolute Delay, 4-Tone Intermodulation Distortion, and P/AR. Requires Option 950RTS-600 (Standard VF Measurements).

950RTS-602 23-Tone Line Quality Analysis
23-Tone Test of Loss, Attenuation Distortion, Envelope Delay, Intermodulation Distortion, Signal-to-Noise, and Return Loss as specified in IEEE P743-1995. Performs complete two-way line analysis in less than 10 seconds.

950RTS-603 ROTL Responder
Near-or far-end Remote Office Test Line (ROTL) emulation. Performs all standard Type-105 Test Line functions. Requires Option 950RTS-600 (Standard VF Measurements).

950RTS-604 ATME - ROTL Responder
CCITT automatic transmission measuring and signaling testing equipment (ATME No. 2) is intended to make transmission measurements, echo canceller tests, and signaling system functional tests on all categories of international circuits terminating in exchanges with 4-wire switching.

950RTS-605 Auto Routining Package
Contains the software drivers and database needed to perform automatic routining on Type 100, 102 and 105 test lines.

950RTS-606 Remote Audio
Provides a 2-way audio link between the circuit under test in a remote 950RTS and a local telephone.

Return to Sage-950RTS Techinical Specifications